Chicago Electric 91995 User Manual Page 1

10” COMPOUND MITER SAWModel91995SET UP AND OPERATING INSTRUCTIONSDiagrams within this manual may not be drawn proportionally.Due to continuing improve

Page 10SKU 91995 For technical questions, please call 1-800-444-3353.The smaller the gauge number of the wire, the greater the capacity of the cord.

Page 11SKU 91995 For technical questions, please call 1-800-444-3353.ASSEMBLY AND OPERATING INSTRUCTIONSNote: For additional references to the parts

Page 12SKU 91995 For technical questions, please call 1-800-444-3353.CAUTION! The Cross Pin (28) should always be activated in the “locked down” pos

Page 13SKU 91995 For technical questions, please call 1-800-444-3353.8. Depress the Spindle Lock (84) to keep the Saw Blade (56) from turning. (See

Page 14SKU 91995 For technical questions, please call 1-800-444-3353.9. Use the Wrench (109) to unscrew and remove the Spindle Bolt (58). NOTE: The

Page 15SKU 91995 For technical questions, please call 1-800-444-3353.1. A workpiece Clamp Assembly (36) can be installed by inserting the Assembly in

Page 16SKU 91995 For technical questions, please call 1-800-444-3353. cannot be seen clearly, disconnect the electrical Power Cord from its electrica

Page 17SKU 91995 For technical questions, please call 1-800-444-3353.To Adjust The Cutting Depth:1. WARNING! Prior to performing this proce

Page 18SKU 91995 For technical questions, please call 1-800-444-3353.HANDLE (1) 6. If the Saw Blade (56) touches the Table (18) or any other part of

Page 19SKU 91995 For technical questions, please call 1-800-444-3353.o2. The bevel angle (or Saw Blade tilt capacity) may be adjusted from 0 - 45 to

Page 2SKU 91995 For technical questions, please call 1-800-444-3353.SPECIFICATIONSElectrical Requirements 120 V / 60 Hz / 1800 Input Watts.15.0 AMPs S

Page 20SKU 91995 For technical questions, please call 1-800-444-3353.6. Plug the Power Cord (102) into the nearest 120 volt, grounded, electrical

Page 21SKU 91995 For technical questions, please call 1-800-444-3353. 3. Daily: With a soft brush, cloth, or vacuum, remove all dust and debris from

Page 22SKU 91995 For technical questions, please call 1-800-444-3353.PARTS LISTNOTE: Some parts are listed and shown for illustration purposes only, a

Page 23SKU 91995 For technical questions, please call 1-800-444-3353.ASSEMBLY DIAGRAMNOTE: Some parts are listed and shown for illustration purposes o

Page 3SKU 91995 For technical questions, please call 1-800-444-3353.Keep bystanders, children, and visitors away while operating a power tool. Distra

Page 4SKU 91995 For technical questions, please call 1-800-444-3353.Avoid accidental starting. Be sure the Power Switch is off before plugging in. C

Page 5SKU 91995 For technical questions, please call 1-800-444-3353.SERVICETool service must be performed only by qualied repair personnel. Service

Page 6SKU 91995 For technical questions, please call 1-800-444-3353.Before using the Miter Saw, make sure the Saw Blade is properly mounted on the Saw

Page 7SKU 91995 For technical questions, please call 1-800-444-3353.The Cross Pin (28) should always be in the “locked down” position when the Saw is

Page 8SKU 91995 For technical questions, please call 1-800-444-3353.Maintain this product with care. Keep the Miter Saw clean and dry for better and

Page 9SKU 91995 For technical questions, please call 1-800-444-3353.GROUNDINGImproperly connecting the grounding wire can result in electric shock.Che